Terug naar blog
Vergelijkingen 2026-11-18 Jewellery Tools UK — Hand Tools for Jewellers & Silversmiths 8 weergaven

Chasing Hammer vs Planishing Hammer: Reading the 22mm Bow Face

Chasing Hammer vs Planishing Hammer: Reading the 22mm Bow Face

A 22mm German bow face hammer can chase and planish — but it is not two hammers in one. Here is how to read the face, the ball peen, and the work each actually suits.

The 22mm bow face is a chasing face, not a planishing face

A chasing hammer and a planishing hammer are often described as opposite tools: one moves metal into pitch, the other smooths it flat. The 22mm German bow face hammer sits on the chasing side of that line. Its generous bow face has a subtle convex curve, and that curve is the point — it lets you displace sheet metal smoothly and consistently during repoussé and chasing without the sharp edge of a flat face digging in.

A planishing hammer, by contrast, is built around a broad, flat or very gently domed face that levels and refines a surface. The bow face here is not that. If you strike with the bow face expecting to planish, you will keep moving metal rather than settling it. The useful comparison is not which hammer is better — it is which face you reach for at which stage of the work.

Bow face vs ball peen: two working ends, two jobs

  • 22mm bow face: Subtle convex curve for smooth, consistent displacement of sheet metal during repoussé and chasing. This is the end for moving metal with controlled precision, not for flattening a finished surface.
  • Reverse ball peen: The ball end is suited to planishing and texturing smaller areas, lending definition and a uniform finish. It is a detail tool, not a substitute for a full planishing hammer over a broad panel.
  • Hardened steel head, wood handle: The head is forged from hardened steel and securely fitted to the handle for reliable bench performance. That construction supports repeated controlled strikes, but the supplied information does not give a head weight or a recommended striking force.

What the 22mm German bow face hammer actually gives you

A bench sequence that uses both ends without confusing them

The supplied preparation step is to prepare your metal and pitch. Beyond that, the record gives two operating actions — strike the chasing tool cleanly, and use the ball peen for planishing — without prescribing angles, force or timing. Treat the sequence below as a way to organise the work, not as a manufacturer's procedure.

  1. Prepare the metal and pitch: Set up the workpiece and pitch before any striking. The record names this as the preparation step but does not specify pitch type or temperature.
  2. Chase with the bow face: Strike the chasing tool cleanly with the 22mm bow face to displace metal in a controlled, consistent way. The convex curve is what supports smooth movement rather than sharp local dents.
  3. Switch to the ball peen for smaller areas: Use the reverse ball peen for planishing and texturing smaller areas, lending definition and a uniform finish. Keep it for detail; it is not a broad planishing face.
  4. Stop and reassess before switching back: Because the bow face moves metal rather than flattening it, check the surface before returning to chasing. The record gives no guidance on how many passes or how much force to use.

Where this hammer replaces a dedicated planishing hammer — and where it does not

For small-scale repoussé and chasing, the 22mm bow face hammer is a refined alternative to heavier general-purpose hammers for detailed forming. Its ball peen covers planishing and texturing in smaller areas, which is often enough for jewellery-scale work where a full planishing hammer would be oversized.

It does not replace a dedicated planishing hammer for broad, flat surfaces. The bow face is convex by design, and the ball peen is a small, rounded end; neither is a wide flat face. If your work is mostly levelling large panels, this is the wrong primary tool. If your work is mostly chasing and repoussé with occasional small-area planishing, the two ends cover the bench nicely.

What the supplied information does not settle

The record does not give a head weight, a handle length, or a recommended striking force, and it gives no care or safety instructions. It also does not confirm suitability for ferrous metals or for heavy forging. Those gaps are decision limits, not defects: they mean you should judge the hammer by its stated purpose — non-ferrous sheet, repoussé and chasing — and by how the 22mm face feels in your hand, rather than by numbers the listing does not provide.

If you need a planishing hammer for broad surfaces, this comparison should send you looking for a flat-faced tool instead. If you need a ball peen chasing hammer for detailed metal movement, the 22mm German bow face is the one described here.

Gerelateerde artikelen

Customer Service
Home
Producten
Winkelwagen
Profiel